200 m³/DAY REFERENCE CONFIGURATION

200 m³/day wall-panel and lightweight-block line

This high-output physical-foaming reference scope connects preparation, metering, mixing, mould circulation, horizontal and vertical cutting, slotting, handling and centralized control. Final output and equipment follow the confirmed product, materials, shifts and factory.

Plan your factory See project evidence

Independent engineeringEquipment manufacturingProject delivery

REAL HENGDE FACTORY EQUIPMENTConnected production modules prepared around a confirmed project scope.

Connected Hengde lightweight wall-material production equipment assembled in the factory

HENGDEENGINEERED AS ONE SYSTEM

200 m³/dayReference production direction

≈280 kWRounded listed connected power

70 setsMould quantity in reference list

VERIFIED REFERENCE SCOPE

Use the equipment list to understand the complete line

The uploaded reference list contains 36 named equipment and tooling items across preparation, cutting, finishing, circulation and electrical control. It is a planning reference, not a universal quotation: final quantities, installed power and output must be recalculated for the project.

Preparation & metering

Two screw feeders, belt conveyor, powder metering, conveyor-linked metering and water metering.

Foaming & mixing

Physical foaming machine, screw air compressor, operating platform, extra-large horizontal mixer, premixer and powered storage bin.

Cutting & finishing

Nine-station horizontal saw, twin-mould three-station CNC vertical saw, peeling, slotting, demoulding and turning equipment.

Circulation & control

Transfer cars, pouring, demoulding and mould-return lines, twin cutting drives, PLC master cabinet and distributed electrical cabinets.

Engineering drawing of the nine-station horizontal cutting section listed for the 200 cubic metre reference line — Engineering drawing — the listed nine-station horizontal cutting section, not a project photograph.

BATCH PREPARATION

Metering, physical foaming and mixing set the production rhythm

ENGINEERING DRAWING

Belt conveying

Reference model HDPDA-001 connects material feeding to the preparation section.

ENGINEERING DRAWING

Water metering

A dedicated water-metering unit controls the confirmed batch input.

REAL EQUIPMENT PHOTO

Physical foaming

Reference model HDKWF1-001 prepares foam for the confirmed physical-foaming process.

Mixing & transfer

The list connects an extra-large horizontal mixer, premixer, powered storage bin and project-selected slurry transfer.

CUTTING & FINISHING

Horizontal cutting, vertical cutting and finishing are separate jobs

ENGINEERING DRAWING

Nine-station horizontal saw

Reference model HDSQ-009 is listed as the main multi-station horizontal cutting section.

Twin-mould CNC vertical saw

A three-station vertical cutting section is listed to connect the required second cutting direction.

REAL FACTORY PHOTO

Automatic slotting

Multi-panel slotting is listed for the confirmed groove or joint profile.

Hengde wall-panel and block clamping system in the factory

REAL FACTORY PHOTO

Clamping & handling

A wall-panel and block clamp, demoulding tool and turning equipment move the product through finishing.

CIRCULATION & TOOLING

Mould quantity and transfer equipment support the nominal output

Seven transfer cars

The reference list includes seven wall-panel transfer cars with corresponding electrical cabinets.

Three line stages

One pouring line, one demoulding line and one mould-return line are listed, plus two cutting-drive lines.

Mould system

The reference tooling scope lists 70 mould sets, 30 mould bases and 20 receiving plates.

Insert system

Rod frames, racks, rods and transfer carts are included for the confirmed panel-production route.

Hengde mould return line engineering drawing for the 200 cubic metre reference configuration — Engineering drawing for mould circulation; final rail length and positions follow the approved layout.

ELECTRICAL SCOPE

Treat listed connected power as a design input, not an operating-cost promise

The source list rounds total connected power to approximately 280 kW. The arithmetic sum of the listed powered items is about 280.65 kW; actual installed scope, simultaneous demand, operating load and local electrical design require project confirmation.

Hengde PLC main control cabinet for a connected lightweight wall-material line — Original equipment photo — PLC and remote functions depend on the delivered electrical scope.

BUYER QUESTIONS

Questions to answer before equipment selection

Does 200 m³/day mean every project will produce exactly 200 m³?+

No. It is a reference direction. Product geometry, recipe, curing, mould cycle, shifts, cutting rhythm, labour and factory conditions determine practical output.

Is every listed machine mandatory?+

No. The reference list explains one high-output route. Final equipment and quantities follow the confirmed product, automation level, site and contract.

Can the same direction cover blocks and wall panels?+

The uploaded list contains both block-line and wall-panel-specific modules. Engineering must confirm which products, moulds, cutting and finishing functions are included in the final project.

SEND YOUR PROJECT INFORMATION

Let engineering review the complete factory need

Tell us the project country, target product, local raw materials, planned output and current project stage.

Full name Country / project location Target product Planned daily output WhatsApp with country code Business email

Available raw materials and factory conditions Project details or questions Optional

Project details help engineering review the product, process, output and factory need. This form uses Hengde's existing inquiry workflow.

NEXT STEP

Start with your product, materials and project location

Engineering can only configure a practical line when the real production conditions are visible.

Prepare your project brief